1. downloads
  2. business software
  3. news
  4. reviews
  5. top apps
Descargar SpeedFan 4.34

SpeedFan 4.34

Por Almico  (Freeware)
Valoración de los usuarios
Publicidad

SpeedFan is a program that monitors voltages, fan speeds and temperatures in computers with hardware monitor chips. SpeedFan can even access S.M.A.R.T. info and show hard disk temperatures.

SpeedFan supports SCSI disks too. SpeedFan can even change the FSB on some hardware (but this should be considered a bonus feature).

SpeedFan can access digital temperature sensors and can change fan speeds accordingly, thus reducing noise.

SpeedFan can find almost any hardware monitor chip connected to the 2-wire SMBus (System Management Bus (trademark belonging to SMIF, Inc.), a subset of the I2C protocol) and works fine with Windows 9x, ME, NT, 2000, 2003, XP and Windows Vista. It works with Windows 64 bit too.

SpeedFan can handle:

  • almost any number of South Bridges
  • almost any number of hardware monitor chips
  • almost any number of hard disks
  • almost any number of temperature readings
  • almost any number of voltage readings
  • almost any number of fan speed readings
  • almost any number of PWMs
Título: SpeedFan 4.34
Nombre de fichero: installspeedfan434.exe
Tamaño de fichero: 1.61MB (1,684,997 bytes)
Requisitos: Windows (Todas las versiones)
Idiomas: Múltiples idiomas
Licencia: Freeware
Fecha añadida: 22 de abril de 2008
Autor: Almico
www.almico.com
Página de inicio: www.almico.com/speedfan.php
MD5 Checksum: 1B3F238E32D68217F5B3DDAE9B246024

4.34
- added full support for SiS964 SMBus
- added full support for SiS966 SMBus
- added full support for ULi M1575 SMBus
- added full support for VIA VT8237S SMBus
- added full support for VIA VT8251 SMBus
- added full support for nVidia MCP61 SMBus
- added full support to read internal temperatures on AMD K10 processors
- added native nVidia video card (up to, but excluding 8xxx) internal temperature reporting
- added full support for SMSC SCH5307
- added full support for F8000 temperatures and fan speeds
- added full support for SMSC EMCT03
- added full support for WINBOND W83793G, including ADVANCED options
- added support for Fintek F71782F hardware monitor at unusual addresses
- added support for Winbond W83627DHG at unusual addresses
- added support for ITE IT8726F hardware monitor at unusual addresses
- added support for a new stepping of the Andigilog aSC7621
- Winbond W83791D properly handles higher fan divisors for fan1, fan2 and fan3 and shows fan4 and fan5 too
- added SMSC LPC47M192 FAN DIVISOR settings in CONFIGURE / ADVANCED
- added full PWM support to SMSC LPC47B397, including settings in CONFIGURE / ADVANCED
- CONFIGURE now allows to go as low as -60C when selecting the DESIRED and WARNING levels to let users of the RELATIVE Intel Core temperature reading properly configure SpeedFan
- improved DDR2 memory module size detection
- added preliminary DDR3 identification
- new icon by Bengt Strom
- fixed an issue where Intel Core temperatures on multi core systems reported the same temperature for all cores
- improved Tjunction detection for Intel CORE temperatures (you might no longer need the temperature offset in CONFIGURE / ADVANCED)
- fixed crash on several DFI motherboards
- fixed the detection of older revisions of the ITE IT8705F
- restored the correct clock speed after resume from hibernation
- rewritten the logic of the usage of a synchronizer in the thread that reads CPU usage (this will fix the SpeedFan not exiting issue)
- address $2E on DFI motherboards is no longer scanned if the motherboard model starts with LP. If you have one of these models and you know that there should be a valid chip at that address, send me a SEND REPORT (INFO tab) with some NOTES
- fixed ADT7475 temperature readings when in offset 64 mode
- fixed a bug when changing the type of data to be charted
- mails sent by SpeedFan now properly separate headers and the body with a blank line
- fixed an issue with SUN 2864 motherboard====

blog comments powered by Disqus